Factors that Lead to Premature Pipe Replacement

Factors that Lead to Premature Pipe Replacement

Your house has a variety of pipes that run through it. The water supply pipes and the sewage pipes are just a couple of the types of pipes you’ll find in your home’s plumbing system. There are also the pipes that run natural gas to wherever you have gas appliances.

While all of these pipes will eventually wear down and need to be replaced, it is the sewage and water supply pipes that are prone to needing early replacement. These pipes come in a variety of different materials and typically last anywhere from 25 to over 100 years. Understanding what types of pipes you have can help you better gauge when they’ll be due for replacement.

Knowing what types of pipes you have can also help you understand what damages them and causes them to corrode and not last the expected service life. Here are the six most important contributors to your pipes wearing out early.

1. Water Quality

Water quality is one of the biggest factors contributing to pipe corrosion. When we think about water quality, it is not just the chemical pollutants we are talking about. Rather, everything that is in the water affects its quality and what it does to your pipes.

For instance, if your water contains a lot of minerals, it is considered hard. Minerals like calcium, magnesium and even iron will build up in the pipes and cause them to corrode. This leads to leaks in the pipes and the eventual need for replacement.

Adding a water softener will help remove these common contaminants and help extend the life of your pipes. Be sure to keep it full of salt, and perform regular maintenance. Also, be sure to replace the anode rod regularly to ensure it can continue to remove the optimum amount of minerals.

2. Subpar Pipe Material

As mentioned above, the material your pipes are made of will determine their regular service life. Common pipe materials include:

  • Galvanized Steel
  • Copper
  • Brass
  • PVC for Drain
  • Cast Iron for Drain

Older buildings also used lead pipes. The biggest issues with lead pipes are health impacts. If your pipes are older than 1986, you need to have your pipes evaluated by a licensed plumber.

Most other materials are of good quality to begin with, but they may lose that quality with poor installation. This is especially true for copper piping, which requires heating to seal with solder. Too much or too little heat will prevent it from sealing properly. This will lead to leaks from the joints and will cause the pipes to corrode from the outside.

If you are not experienced with sweating and sealing pipes, leave the installation to the professionals. If you attempt to tackle it yourself, you risk creating major problems, including flooding, water damage and further damage to your pipes.

3. Using Caustic Cleaning Products

Cleaning products have come into central focus for many reasons. Many consumers are becoming sensitive to what these chemicals do to their health. However, most homeowners have no idea what they do to their pipes.

Many cleaning products have bleach in them. While this is okay in products that are designed for pipes, other applications of bleach can accelerate the corrosion process. This bleach reacts with organic matter, releasing toxic fumes and corrosive compounds.

If you have plastic pipes in your home, the danger is in the heat caused by the chemical reaction. This heat can eat through your pipes, as well as warp them and cause them to leak. Once the pipes are weakened, they will have to be replaced to prevent damage from leaks.

4. Vibration in the Line

Water supply pipes are under pressure and, as such, are prone to vibration. These lines are secured to reduce possible damage. However, these brackets will eventually work loose and can damage the pipes and cause leaks.

Newer pipes are made of flexible materials that are less prone to vibrational damage. However, there are plenty of areas where vibration may cause an issue. Pipes connected to these appliances are susceptible to more vibration issues:

  • Refrigerators
  • Washing machines
  • Dishwashers
  • Water coolers

If you suspect your lines are damaged by vibration, call a licensed plumber to evaluate your pipes. If you catch the damage early enough, you can further secure the pipes and replace only the sections that are damaged.

5. Excessive Buildup

Pipes are prone to various kinds of buildup beyond minerals if you have hard water. Consider bathrooms and all the products you use to clean your body. While people do enjoy taking long showers, brevity is valued to reduce water consumption. However, without properly flushing the drain, these chemicals will harden over time.

Kitchens are another source of excessive buildup, especially if you have a garbage disposal. While it is nice to think that a little dish soap may clean all the grease away, rinsing this down the drain can cause significant damage to your pipes.

The key is to be careful of what you flush down your drains and then to ensure you are using enough water to flush it through your system. If you find your drains are constantly running slowly or your toilets are clogging, it is very likely you have a significant buildup somewhere in your system.

6. Roots and Trees

Mother nature is a powerful foe to your pipes. Trees and large shrubs don’t pay attention to your pipes. Instead, they go ahead and push through where they want to go. If you have trees in your yard, keep an eye on where the roots are going. If you have a slow drain or a backup from well down your line, you may have a root problem. Likewise, if your water lacks pressure, you may have a root that has penetrated your outside pipes.

A licensed plumber will run a camera down your pipes to inspect them and see if there are any roots or other obstructions. This will allow you to find the root problem—no pun intended.

If a root is discovered, you may be able to clear the root and salvage the line. However, if the damage is extensive, you may need to repipe the section. Our team is experienced and equipped to run trenchless sewer piping if you need to run a new sewer line.

What to Do If Your Pipes Are Aging Prematurely

If you think your pipes are prematurely corroding, the licensed plumbers at Christian Brothers are here to help. Whether you need to inspect for roots or leaks or have your piping evaluated, our plumbers have the experience to help.

Servicing Glendale since 1976, our licensed plumbers can handle everything from leaks and clogs to repairs and replacements. Hot water heaters, sinks, toilets and softeners are no problem for our team. Our team even has professional technicians and electricians to handle heating, cooling and electrical problems. Give us a call today to schedule your consultation.

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


What is Hydrojetting?

What is Hydrojetting?

As your home ages, debris and other pieces of junk naturally pile up in your pipes. If you let this go unattended, it will form blockages that could take ages to get rid of. It’s essential to address this issue right away, and hydro jetting is one of the latest ways to do so. Hydro jetting is a powerful process that restores your pipes to their original state. Hydro jetting is an alternative to other options and is a solid choice for a lot of homeowners. Let’s take a look at what hydro jetting is and the pros and cons that it offers.

What is Hydro Jetting?

Simply put, hydro jetting is the process of shooting a high-pressure stream of water through pipes to clear out any debris inside. You might be familiar with weaker forms of hydro jetting. If food has ever gotten stuck in your kitchen sink, you’ve likely plunged it with hot water to break up the stoppage. If your toilet has clogged in the past, you’ve probably used a plunger to open it up with a strong force of water.

Hydro jetting takes this concept to the next level. Hydro jetting uses a special machine, a contraption that attaches a hose to a source of water. When a technician turns on the machine, an extremely high-pressured stream of water comes out of the nozzle. This stream is directed into the pipe to clear it of any gunk. People often use warm water in tandem with hydro jetting to loosen the stoppage as much as possible.

Contrary to popular belief, the goal of hydro jetting doesn’t have to be to break through a heavy blockage that has been plaguing your pipes for ages. Hydro jetting is a very sensible option to clean the interior of your pipes simply. Although water might flow normally, mold and mildew could be lining the pipe’s interior. This leads to corrosion in the long run and potentially even contaminated water if these particles are near the water source.

Why Use Hydro Jetting?

Hydro jetting is useful for several reasons. First of all, it is extremely powerful. It’s hard to emphasize just how strong that stream of water is and how much force it generates. If there are many years’ worth of debris lining the inside of a pipe, you’ll need an equally serious method of getting it out. Hydro jetting achieves just that. In addition, hydro jetting is well known to be friendly for the pipe itself. In comparison, driving some sort of snake through the pipe can cause permanent damage to the surface of your pipes.
For older homes, the metal is already likely to be corroding, and friction between the snake and the pipe can cause a rupture. This will force you to buy a new pipe altogether, which is much worse than a small clog, to begin with. Hydro jetting is also known to be relatively inexpensive. There aren’t really any other costs besides the hydro jetter itself and a supply of water. The energy cost that hydro jetting uses are minimal compared to much more extravagant projects. Setting up hydro jetting is a very straightforward process as well. Once you have the device, all you need to do is plug it in and aim the nozzle at the appropriate place. You can either attempt this yourself or call upon a professional service for guidance.

Cautions While Hydrojetting

At the same time, hydro jetting isn’t a magical solution to all of your clogging problems. While it’s effective, you have to use a certain degree of caution while using this equipment. Water and electricity don’t fundamentally mix. You are going to be shooting a large volume of water while operating a motor on the other end. If the two come into contact, this is a recipe for disaster. Although there are precautionary measures such as rubber guards on the handle and engine, you need to be careful.

Before starting the stream of water, make sure you know where the nozzle is pointed towards. If you ever lose control of the device, immediately shut it off so you can regain control. Hydro jetting can also damage the pipe if done improperly. A professional technician will know how to correctly aim the stream of water so as not to come in contact with the wrong parts of the pipe. As discussed earlier, snaking can be harmful if done carelessly. Similarly, hydro jetting is a safe procedure if you know what you are doing. Anything less, and you’re back to step one with dangerous ways of clearing your pipes.

When to Hydro Jet

It’s crucial to note that there are situations where you should and should not hydro jet. For starters, hydro jetting is a great idea when you can’t see the clog. If the backup is within sight or a straight line, it might be simpler to try another method of clearing the clog that has less effort involved to get the job done. There’s no need to escalate the issue when a simple solution will do.

For backups that are further down the pipe, hydro jetting is well worth considering. The main question is whether your pipes will be able to sustain the pressure of hydro jetting. The sheer force of the water could cause permanent damage to utilities in older homes. If you know for a fact that your pipes are already unstable, hydro jetting introduces a serious risk of collapse. At that point, you’re better off just replacing the pipes altogether as no solution will be gentle enough.

Lastly, hydro jetting is generally recommended for indoor pipes. When everything is indoors, you are looking at a controlled environment that isn’t at the mercy of the natural elements and climate. Hydro jetting in an indoor setting ensures that the setting is room temperature, and the water won’t be overly warm or cold. On the other hand, if the pipes are outdoors, the environment is much more volatile. In freezing temperatures, hydro jetting could result in icicles or frost. This is the absolute worst thing that can happen to pipes, and you’ll undoubtedly need to replace them. If the outdoor temperature is anywhere near freezing, think twice about hydro jetting pipes that run through the ground.

Hydro Jetting in Your Home

By now, you might be interested in hydro jetting in your own home. Perhaps you’ve lived in the house for many years, and it is about time to renovate the kitchen and the bathroom. You want to clear things up before you make any significant changes. As mentioned above, hydro jetting isn’t the most straightforward task if you’ve never done anything like it before. It’s in your best interest to contact a professional service such as Christian Brothers Air Conditioning, Plumbing, and Electrical in Glendale, AZ. We know all about hydro jetting and why it is the solution to your clogging issues. Our team members are experienced with all the proper equipment and procedures and can hydro jet your pipes in a matter of hours.

In addition to hydro jetting, we offer burst pipe repair, outdoor lighting services, and emergency plumbing repair, as well as indoor air quality assessments and solutions. For a free and quick consultation, please call us as soon as possible! We’d love to work with you and introduce you to the fantastic world of hydro jetting.

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


How Often You Should Have A Plumbing Inspection

How Often You Should Have A Plumbing Inspection

Taking care of a plumbing system must be a top priority for a homeowner. Many homeowners do know that delays on repairs wouldn’t be helpful, so they move to address leaks, clogs, and other issues right away. They might not move as quickly to replace and to upgrade aging plumbing, though. One reason is that nothing seems to be wrong with it. Another could be the homeowner can’t recognize the signs of aging drains and pipes. If the homeowner makes an error in judgment here, he or she could face a plumbing disaster.

Sometimes, a problem might be a hidden one. A leak occurring far out of sight can persist until its damaging results become apparent. And here, too, the homeowner could face significant plumbing repair bills. Catching the issue might have led to a less-costly outcome. If the homeowner doesn’t know what to look for, how can he or she discover a problem? The answer is to turn the job over to a professional. A plumbing company would happily provide a thorough inspection when asked. If you’re wondering how often should you request a plumbing inspection, here are a few tips for scheduling this necessary service.

Common Recommendations for Inspections

Requesting an inspection once every two years would allow many residential and commercial property owners in Glendale to uncover any problems present with the system. Allowing three or four years to pass would be a bit too long. A lot can happen in 36 to 48 months. Waiting so long could leave a problem in place for too long. Calling in an inspection every two years would be reasonable when the plumbing system is already in decent shape. If the first inspection reveals nothing is wrong or leads to immediate repairs, the plumber could recommend a standard two-year review.

Not all plumbing systems are in perfect shape, though. Maybe keeping a more consistent eye on the plumbing system would be a good plan. If asked, a plumbing company would surely accommodate a once-a-year inspection plan. When the home is an older property, a yearly inspection could be preferable to one performed every two years. Older homes suffer from age-related problems, and those issues could get worse without necessary upkeep. More frequent inspections could help the cause.

Requesting an Inspection When Concerned

Sometimes, the things that go bump in the night might come from your plumbing system. Avoid the trap of explaining away the problem. People tend to do this to put off spending money on repairs due to the cost or the inconvenience. They comfort themselves with the assumption that there isn’t really anything wrong. Ultimately, reality reveals itself. The light tapping sound of a leak above the ceiling is only going to cause more damage to the wood and drywall. A different result could be the case when catching the problem earlier.

When something appears out of the ordinary, consider it a good idea to ask a plumber to perform a thorough examination, and take the opportunity to explore the plumbing system for any not-so-obvious problems. Just because one or two things are wrong with the plumbing does not mean the entire plumbing system is in bad shape. Then again, severe problems could be present throughout the home. You won’t know for sure until a skilled pro takes a look. Still, locating and correcting defects right away saves time, money, and aggravation. In Glendale, AZ, Christian Brothers has long established itself as a top plumbing company. Clogs, leaks, drain cleaning, and even pipe relining are among the jobs handled by the team.

Consider Seasonal Inspections

The seasons of the year could contribute to the timing of your annual inspections. Right before winter seems like a plan for many because they worry about serious problems such as potential pipe freezes during the cold weather months. Nothing is more worrisome to many homeowners than the damage that frozen pipes may cause, so the concern is well-founded.

In truth, there is no improper time of the year to schedule a plumbing inspection. That said, those with concerns about winter weather could also find requesting a check once the temperature heats up to be reassuring. Even if nothing appears wrong, concerns might exist about the plumbing’s fitness for the winter. Perhaps it would be a good idea to winterize the system to reduce the chances of problems in the future.

Examinations Involve a Vast Plumbing System

Even in a small house, a plumbing system covers a lot of territory. In a midsize or large home, the drains and pipes sprawl throughout the interior and may be hidden in many places. With so much plumbing to worry about, it becomes almost impossible to stay on top of everything. You have plumbing running throughout the bathroom, kitchen, washing machines, and more. Maybe you have a bathroom or sink inside an attic or basement that you don’t pay much attention to. Those plumbing systems may house pressurized water in their pipes. Things could go wrong and create many unwanted headaches or hassles.

Probably the most concerning plumbing components would be the ones inside the walls. Plumbing that runs underneath the house in a crawlspace, while out of sight, can’t be ignored. If something goes wrong with plumbing that you can’t see, you won’t know how serious the issue is. Once again, you might not know about a leak until the damage becomes both evident and extensive.

A modern plumbing company can deal with out-of-sight problems. Leak detection systems that employ infrared cameras and other devices could find a leak hidden from view. Remember, even though you can’t see the leak, the leak may be causing harm. A skilled plumber usually knows how to perform the right fix in the least invasive way possible.

Warnings About Potential Hazards

There might not be a problem present right now, but things could degrade. A plumber could look at the pipes and notice they might need an upgrade in a year or so. The plumber might see other impending problems and provide recommendations for improvements. At least with a heads up, the homeowner can make suitable arrangements. If you live in an older home with the original plumbing lines, an upgrade may be unavoidable. Knowing how much time you have before performing required upgrades allows for better planning and budgeting. You certainly don’t want to wait until leaks, corrosion, and other problems arise. Performing an early fix through preventive maintenance might be preferable.

Avoid Delays on Repair Work

Once any mysterious trouble becomes uncovered, the plumber can take steps to fix things. Of course, the professional needs a go-ahead from the homeowner. Avoid putting off any necessary repairs. Doing so increases the risks that things could turn out worse, and that situation wouldn’t be beneficial.

Do you want a plumbing inspection performed right away? Call Christian Brothers plumbing to request assistance with your plumbing woes. The team also handles air conditioning, electrical, and heating work. In business since 1976, the Christian Brothers team brings licensed home service to your door.

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


Common Plumbing Code Violations To Be Aware Of

Common Plumbing Code Violations To Be Aware Of

Various plumbing codes, including the IPC (International Plumbing Code), have developed over decades in Arizona and throughout the U.S. Most are mandatory requirements that will keep you from running into costly and possibly dangerous problems with your pipes and fixtures. However, just because these codes exist doesn’t guarantee that they will be heeded. In fact, plumbing code infractions are some of the most common violations you can find in homes today, principally because there are a lot of DIY plumbers out there who don’t have a lot of experience with the provisions. Becoming familiar with some of the most common plumbing code violations can be valuable for homeowners, home shoppers, and real estate professionals.

Drain Pipe With Wrong Slope

The most optimal slope for drain pipes is 1/4 inch per foot. In some jurisdictions, the slope may be as little as 1/16 inch per foot. Regardless, under-and over-sloped pipes are common problems that often result in severe blockages. If the slope of the drain pipe is inadequate, then the wastewater won’t have enough gravitational force to cause it to drain properly. If there is too much slope, then the wastewater will flow too quickly and likely leave solids behind.

Improper Spacing Around Bathroom Fixtures

To be properly up to code, each fixture in your bathroom must have a certain amount of space around it. This space requirement is essential for the safe and proper use of the fixtures. Keep in mind that when reviewing the space requirements, measurements start from the drain or the center of the fixture and not the fixture’s edge.

Most codes dictate there be at least 21 inches of space in front of your sink and toilet. As far as side to side is concerned, there must be at least 15 inches of space between the center of the toilet or sink and the wall and 30 inches between them and the drains of other fixtures.

Improperly Installed TPRV Pipe

The temperature pressure relief valve is an important safety device that prevents your water heater from turning into a bomb. Its job is to make sure the water heater tank doesn’t take on more pressure than it’s designed to handle. Without this valve, the tank’s pressure will continue to increase, and the water inside will become superheated past its normal boiling point until the tank explodes.

A discharge pipe should be connected to the TPRV. This pipe’s job is to take on the water released from the TPRV and route it to a proper discharge location. Most plumbing codes give specific instructions regarding the discharge pipe.

Most codes require that the pipe:

  • Be constructed of approved metals and plastics, such as CPVC, copper and polyethylene
  • Not be the same size or larger than the valve to which it’s connected
  • Not be longer than necessary
  • Be as straight as possible
  • Be installed in such a way that gravity causes it to drain
  • Not contain a trap
  • Flows into a floor drain or outdoors
  • Not connect directly to the drainage system
  • Discharge through a visible air gap in the same room as the water-heating appliance
  • Discharge to a termination point that is readily observable by occupants
  • Not contain valves or tee fittings
  • Not have a threaded connection at the end so as to avoid capping

There are even more requirements, which is why TPRV discharge pipes commonly have code issues.

Insufficient or Missing Air Gaps for Fixtures and Appliances

To prevent wastewater from making its way into the freshwater lines, there needs to be a minimum air gap between the tap or water outlet and the flood line of a sink or fixture. With this gap, there is no danger of the wastewater making its way into the tap or water outlet in case the sink overflows.

With dishwashers, air gaps operate a little differently. A dishwasher air gap is a small cylinder-shaped piece of equipment that is installed next to your kitchen faucet. They have been in existence for a long time but were not required in many states until recently.

Insufficient Number of or Missing Cleanouts

A cleanout is a location in your piping system that gives you access to your sewer pipe. Cleanouts are important because they make diagnosing and fixing pipe and sewer problems relatively easy and convenient. They are usually located outside somewhere, often in the lawn, and have a screw top opening.

According to code, cleanouts are necessary for horizontal pipe runs of 100 feet. They are also required within 10 feet of where the drain connects to the sewer. Additionally, cleanouts are required when there’s a change of direction with your pipes that is more than 45 degrees.

Inaccessible Cleanouts

In order for a cleanout to be useful, it must be placed in an accessible location. However, this does not always happen. There should be 18 inches of clearance in front of each cleanout or 12 inches for pipes that are 2 inches or smaller. Cleanouts that are located in concealed piping with less than 24 inches of vertical clearance must be positioned above the flooring or placed outside of the structure.

Unvented Traps

Traps maintain a barrier between your fixture and the sewer system of your home. Generally, you’ll see two types of traps when dealing with bathroom and kitchen sinks — P-traps and S-traps. S-traps are essentially two P-traps that are connected and form the shape of an “S.” The problem with S-traps is they don’t allow for venting.

Venting allows for the entry of air into your plumbing system. This air will help the wastewater flow correctly while allowing for odors and gasses to escape. Vents normally run up through the roof. Without venting, you risk sewage backing up into your fixtures.

Call the Pros for Dependable Plumbing Work

There are a lot of DIY plumbers who do their own pipework for bathroom and kitchen remodel projects. In some cases, these DIYers are skilled and knowledgeable. They may even be plumbing professionals. However, in most cases, the work they do is not up to code and will need to be corrected. If you want your plumbing updates to be done properly, your best bet is to call in the pros.

At Christian Brothers Air Conditioning, Plumbing & Electrical, we’ve got years of plumbing experience and hundreds of satisfied customers. If you’re in need of plumbing done right, then contact us. Our crew has corrected plenty of problems caused by DIY projects. No matter what may be wrong with your pipes, we’ll find a solution.

We also offer an array of heating and cooling services, including AC repair and maintenance, ductless mini-split repair and maintenance, and heating repair and maintenance. Additionally, we have licensed electricians who can provide you with a whole host of electrical services, from electrical repairs and installations to electrical inspections. Call Christian Brothers in Glendale, AZ, for more information today.

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


How To Light The Pilot Light on Your Hot Water Heater

How To Light The Pilot Light on Your Hot Water Heater

If you’re suddenly stuck with only cold water, you may need to ignite the pilot light on your hot water heater. This is an important part of having the system running properly. You can do this relatively quickly if you follow a few easy steps.

Automatic Water Heater Pilot Light Procedure

For those of you who have an automatic hot water heater, you’re going to have a small button that’s called an “ignition” button on the small box that’s sticking out of the side.

If you see that button, follow these steps. First, turn off your hot water heater by setting the “pilot / on / off” button on the small box to “off.”

Wait five minutes at this point so gas can clear out and so that you do not start a fire. Also, set the temperature on the hot water heater to “low.”

At this point, just hold down the pilot button and press the ignition button at the same time. The pilot light will then be lit! Keep holding down the pilot button for 30 seconds. After that, you are finished.

Manual Water Heater Pilot Light Procedure

If you don’t have an “ignition” button, then you have a manual hot water heater. If you’ve got a manual system, you’ll first remove the plate on the side of your hot water heater right below the box that’s sticking out on the side with the buttons on it.

After that, check the interior for an additional plate. Remove that plate as well if needed. You’re going to look for a pipe or multiple pipes that lead up to your burner. That’s what you’re going to light.

Make sure you’ve got a very long light. Then, set the “pilot” button or dial to “off.”

At this point, wait five minutes so that any gas can clear the surrounding area. Next, set the temperature to “low.”

Then, turn the pilot button or dial to the “pilot” setting and press down and hold it while using your very long lighter or long wooden match to light the furnace’s burner.

Remember to hold down the pilot button for a full 30 seconds. After that, set the temperature back to the preferred setting for your furnace.

Christian Brothers Air Conditioning, Plumbing, and Electrical can lend a hand if you have any issues lighting your pilot light. We offer plumbing, HVAC and electrical installation and repair services. We have been voted the #1 plumbing company in Glendale, Arizona, for over 40 years. Contact us today to learn more.

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


What Should You Never Put Into a Garbage Disposal?

What Should You Never Put Into a Garbage Disposal?

Garbage disposals are handy for taking care of food scraps. However, some things can clog your pipes or damage the garbage disposal. Here are some things you should never even consider putting down your kitchen sink’s drain.

Fibrous Fruits and Vegetables

Corn husks, celery, asparagus and banana peels have fibrous strings that will wrap around your garbage disposal’s blades. This can lock the blades up, making them inoperable.

Animal Bones

Garbage disposals aren’t made to handle animal bones. They can easily damage your disposal’s blades, resulting in your needing to get a new disposal. If the bones do make it past the blades, they are likely going to get stuck in the pipe, causing an obstruction.

Grease and Oil

Once these are cool, they become solid. They can easily block your pipes. Oil and grease should be tossed in the garbage once they have cooled.

Beans, Pasta, Oats, and Rice

All of these absorb water. If any gets caught in the drain it can expand and cause a clog to form.

Pits and Seeds

These can easily damage your garbage disposal. They are very hard and should be thought of as a type of wood. Even unpopped popcorn kernels should be thrown in the trash.

Coffee Grounds

Coffee Grounds won’t hurt your garbage disposal but can clog your pipe. They will settle in the pipe, eventually causing a clog.

Eggshells

Eggshells have a thin membrane on the inside that can wrap around a garbage disposal’s blade. They should always be thrown in the trash.

Your Local HVAC, Plumbing, and Electrical Experts

Christian Brothers: Air Conditioning Plumbing Electrical has been helping businesses and individuals in the greater Phoenix area since 1976. We handle kitchen plumbing should your garbage disposal or pipe need servicing. We can also help you with heating and cooling, plumbing, electrical and water heaters. Give us a call today at our Phoenix, AZ, office to find out how we can serve you.

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


A Quick Guide to Sink Installation

A Quick Guide to Sink Installation

 

Q: How do I install a sink in my bathroom or kitchen?

Installing a kitchen or bathroom sink is a significant home project that can be somewhat tricky to accomplish your first time around. However, it is very possible to complete this project if you follow the correct steps throughout the process. Therefore, we’ve compiled a list of these steps to follow, as well as some other things to consider when venturing on this DIY endeavor.

  1.     Take accurate measurements

Before even thinking about the mechanics of how a sink would be implanted in your kitchen or bathroom, you need to consider the more common-sense aspects of the project. This would include measuring the counter top hole your new sink will be going into and writing them down. After writing them down, make sure to take them with you to the store where you will be shopping for a new sink and compare them to the sink you have in mind. The measurements go beyond just the length and width of you sink, but the depth as well. If a sink fits too deep, you’ll need to lower the pipe leading to it. This will require professional assistance. Also, be sure to take note of whether the sink has square or rounded edges. Remember, measure twice just to be safe! Sometimes water damage can cause your counter top to swell, thus making previously accurate measurements now inaccurate. Plus, this water damage is not visible from the top of the counter and it may be worth it to you to get a new counter top to go along with your new sink.

  1.     Assess the Accessories

While buying this new sink, be sure to remember the features of the sink hole in your counter top, specifically the holes. Some sinks may have very large, very small, or multiple faucets and handles. It is crucial that your faucets, handles, and knobs all fit correctly before purchasing your new sink. You can do this by measuring each sink hole, writing them down, and taking them to the store to compare.

  1.     Remove the old sink

This step can be complicated, which is why we’ve decided to break down a normal sink removal into precise steps:

  •   To begin, snap a quick photo of your old sink in the counter top as a reference point. You may need it later.
  •   Shut off all the water, including hot and cold. Also, if applicable, shut off the garbage disposal.
  •   Disconnect all the pipes and drain connections between the plumbing and the sink. Then, disconnect the garbage disposal. Be sure to have any towels ready in case any water is still in the pipes.
  •   With caution, remove the sink clamps if the sink is meant to be removed from the top. If your sink is supposed to be lowered to be removed, releasing these sink clamps will cause it to fall on you. Try to find someone to help you with this step, as the sink might be very heavy, and you will need to either lift it out over the countertop edge or from underneath the sink cabinet.
  1.     Preventive care

When the old sink was removed, you probably noticed the used caulk now around the hole. Be sure to use a pudding knife to scrap that old caulk off. This is also a good time to replace any old supplies, like worn or leaking shut off valves.

  1.     Test fit

After replacing any old material that may need to be removed, take your new sink for a spin. Move the sink in place on or under the counter top to see if it fits correctly. It should be snug and be able to fit through all the necessary holes. Don’t forget to look underneath and inspect the depth of the sink as well. If all comes back good, clean the sink thoroughly. If you can, try to install the faucet head before putting the sink in the countertop. This will make finding the connections easier.

  1.     Install faucet

For this step, consult the manufacturers manual. They should have all the details for the installation process in the manual itself.

  1.     Wrapping everything up

When finishing off this project, use 100% silicone caulk when installing the sink. Line the caulk around the hole of the sink and install new sink clips. Secondly, reconnect any water supply lines and drain tubes. Lastly, connect a garbage disposal, if necessary, and run the sink to check for any leaks. Once you’ve ensured there are no leaks, you’ve done it! Congratulations.

 

Remember, if you run into any problems along the way, do not hesitate to call us here at Christian Brothers. We can have an expert technician to your home that day to help you with your new sink

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


AC Mistakes and How to Avoid Them

AC Mistakes and How to Avoid Them

AC Mistakes and How to Avoid Them

Air conditioning is one of the greatest inventions of the past century. It revolutionizes how we live as well as where we are capable of living. If you live in the great state of Arizona, you probably understand this all too well.

The Phoenix valley area specifically is one of the hottest cities in the entire world. With temperatures in most months reaching over 100 degrees on a daily basis, it makes sense that it is among the hottest places to live. Due to this extreme heat, having a fully operational air conditioning unit and efficient HVAC system is very important. This goes for your quality of life as well as your safety and overall health.

However, despite the importance of having a fully functioning air conditioning unit, some homeowners still make mistakes with AC maintenance and home repair.

Though common in nature, these mistakes can add up to your air conditioning unit breaking down or needing replacement. Not to mention the fortune you’ll be spending on energy bills.

We here at Christian Brothers AC, Plumbing, and Electrical don’t want you to be left out in the heat of the day. We’ve compiled the most common air conditioning mistakes homeowners make to help you avoid costly repairs and premature replacements.

Common AC Mistakes

Here are the mistakes you should be avoiding when dealing with your air conditioning unit. Remember, if you’re in need of repair or have a question, call Christian Brothers as soon as possible.

Avoiding Maintenance

We hear about this too often in our line of work. Homeowners who shy away from maintenance usually end up paying higher prices on repair. Likewise, your air conditioning unit will need replacement sooner rather than later.

It’s always in the homeowners best interest to perform maintenance on their AC unit. Here are a few tips to help you out:

  1. Change your air filter- This is important to the health of your unit as well as your pocket book.
  2. Clean your unit- Doing this will prevent any rocks or debris from blocking the rotation of your units fan.
  3. Make sure no ducts are blocked- A blockage could impede your units ability to circumvent air into your home. Thus causing it to work harder and use more electricity.
  4. Call Christian Brothers for an AC Tune up!– When you call us, we will give you only the best! We’ll have your air conditioning running more efficient than ever.
Phoenix Heating & Cooling

Old Thermostat

Many times we see homeowners who are suffering in their energy bills and AC repairs due to an old thermostat. This is a critical piece of equipment to your HVAC unit. It is very important that you keep it up to date!

With new age thermostats, you have the ability to control the temperature in your home from the palm of your hand. New technology lets you control your homes temperature with a phone app! This can save you plenty on energy bills and is very convenient.

We recommend purchasing the Honeywell Lyric thermostat! It has the all the functionality you could want. As a plus, its relatively user friendly. Be sure to check out our post on the Honeywell Lyric thermostat in our blog.

Poor Indoor Air Quality

If you’ve been sneezing quite frequently lately or wheeze slightly, it may be the quality of your air! This is not only bad for your health, but also for your air conditioning unit. Poor air quality is a sign of a dirty air filter that needs to be replaced.

However, this isn’t the only thing that may be wrong. When your air filter is too dirty, it means your air conditioner is working harder to cool your home. This will cost you a small fortune in energy bills each month.

If you want to improve your health and the efficiency of your unit, take into consideration the quality of the air in your home.

Not Using Ceiling Fan

Not using your ceiling fan can put you at a significant disadvantage with your air conditioner. It all starts with the overall purpose of having a ceiling fan. Ceiling fans are made, obviously, to cool the room.

When the rooms are cooler because of the ceiling fan, it means the air conditioning does not have to work too hard to get the house cooler. This saves your air conditioning from over exerting itself.

If you’re not using your ceiling fans, you’re not helping to keep your air conditioning functioning as well as it could.

AC Repair and Maintenance

Call Christian Brothers

If you’re in a tough spot with your air conditioning unit, or have another HVAC problem, give us a call. We will send our licensed and trained HVAC technicians to assess, diagnose, and repair any issue! We don’t want you to be left out in the heat! Call us today!

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


AC Tune Ups: How Important are they?

heating and cooling systems

AC Tune Ups: How Important Are They?

AC Tune Ups: How Important are they?

When we talk about AC Tune ups its important to know exactly what we’re dealing with. Similar to a pipe inspection for your plumbing or scheduling a yearly physical with your doctor, an AC tune up acts as preventive care for your unit.

Taking time to schedule an appointment is never easy. It seems like there is always something on the schedule. However, with the efficiency and savings you’ll receive, AC tune ups are incredibly beneficial to the homeowner.

Despite this benefit, it seems like most homeowners tend to avoid scheduling AC tune ups. That is exactly why we want to make a list of all these benefits!

Benefits of an AC Tune Up

1. Cost savings

Many homeowners forget the amount they will save if they have a fully top notch functioning unit. A well maintained unit can save you up to 15% on your energy bill each month. Imagine saving that much every month of the year! You’d be adding to your bank account as well as have a comfortable home.

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.


Water Softeners: The Pros and Cons

$100 off water softeners phoenix az

Water softeners are beneficial for a lot of different reasons. However, they have some drawbacks as well. Due to these various pros and cons, many homeowners wonder if installing a water softener is right for them. At Christian Brothers, we want you to have all the information you need to make a clear and calculated choice on this matter. In this article, we provide a snapshot of what to expect from a water softener. Firstly, let’s start with what a water softener does.

Water softeners are water conditioning systems that remove certain minerals in your water that cause the water to be hard. Water that is hard tends to have an excess amount of these minerals and can cause scaling and buildup. As a result of this buildup, you will need piping repairs more frequently and experience more problems in your plumbing. We’ll go over this a little bit later on.

Basically, a water softener acts as filter that prevents this hard water from getting into your home plumbing system. 

There are plenty of great things about having a home water softener but they also come with a few challenges.

Benefits

  • Household appliances last longer- When you have hard water, your household appliances tend to wear down at a faster rate. This is due to the minerals that exist in hard water that filter out in soft water systems. The rate can even move as fast as 30% quicker in deterioration. You’ll also be able to cut back on maintenance cost of your pipes and appliances.
  • No more stains on dishes- This is a little benefit to add to the list. With a water softener, you won’t have water stains on any of your dishes when cleaning them.
  • Healthier skin and hair- Another benefit! Soft water provides you with a cleaner and clearer skin. Also, your hair will be shining like never before!
  • Better lathering soap- With a water softener, the water that comes into your home will be easier to lather with soap. Thus giving your dishes, counter top, and sinks a sparkling shine. This will also make the soap more effective and easier to use! This means you won’t need to spend tons of money on buying new soap because you’ll be using it at a slower rate.
  • Bright colors in your clothes- When you have a water softener, your clothes will be given a brighter coloring. Hard water tends to strip colorful clothes of their visual brightness. Luckily, when you have soft water, you’ll see that radiance after every wash.

Drawbacks

  • The cost of operation- Unfortunately, water softeners do require a little bit of electricity to be able to function properly. This can add up to be quite a bit. If you’re looking to get a water softener, be sure to take this extra cost into account.
  • Potential water waste- Sometimes water softeners tend to waste a good bit of water. Usually its no more than 20 gallons per regeneration cycle. Although that might not seem like a lot, it can add up to be a significant cost on your sewer bill.
  • Environmental consequences- This is something to keep in mind if you are environmentally conscious. Water softeners can waste water, which is obviously not a great thing to the environment around your home. This is something to consider when purchasing a water softener.
  • Installation costs- When you install a water softener, there will most likely be some costs that come with the installation. Luckily, with Christian Brothers, we can install a softener in no time flat. Though there will be a cost to the installation, we can make it as easy and simple as possible!
  • Slippery water- Soft water can be slippery! If you don’t want to have a slipping hazard in your home, you may want to avoid getting a water softener.

Our Recommendation

In Arizona, having a water softener is something that we believe is greatly beneficial. Due to the extreme heat, your skin might need the extra cleanliness. Also, avoiding scaling in your pipes and increasing the longevity of your household appliances is also ideal. We here at Christian Brothers highly recommend installing a water softener in your home. We can have a licensed, experience technician to your home in no time to help you install!

If you are ever in need of any plumbing, air conditioning, or electrical work, please give Christian brothers a call. We believe in servicing our community in the best way possible. By giving the best customer service possible and providing precise repair. Call us today at 623 499 9794.

 

 

Air conditioning, Plumbing, Electrical repair since 1976 in Phoenix, AZ.